HHO Hydrogen Generator Kit 1 Cell with Dryer for Gas and Diesel Engines. Convert any gasoline or diesel engine to run on a mix of Hydrogen, Oxygen, Water Vapor by using your engines vacuum and air flow to assist in the metering of HHO gas made from electricity, electrolyte, and stainless steel plates. Has tested Hydrogen Technology and has verified it increases mileage on gas, diesel, and rocket engines. I discovered this technology in 1970 when I read an article in popular science magazine. The article was about researcher Yull Brown and his important discovery with hydrogen gas in 1968. He realized that you didn’t need to separate or store the gases of Hydrogen and Oxygen. That you could use these gases immediately as they are created by electrolysis. This was the first on demand use of Browns Gas, a name he gave his discovery. Over the years the name was changed to HHO Gas. He was the first person to install a HHO Gas unit on a automobile in 1968. I’ve always loved the science of technology and started to experiment with different types of Hydrogen Generators in the early 70’s. I’ve spent many hours of trial and error over the years. There is a lot to consider when building a HHO unit, Example: Spacing of plates, voltage, proper amount of electrolyte to use, water levels, ect. The HHO Generator that I make is the same exact unit I use on my vehicles and the vehicles I have worked on for many years. As a mechanic for over 45 years, I can testify that this technology works. The HHO Generator with Dryer that I build is Safe, Low Maintenance, and will produce a constant supply of Hydrogen Gas for your vehicle. With no modifications to your vehicle computer or oxygen sensor. Because your not over producing Hydrogen. With my system your engine will be metered the right amount of HHO at idle and above idle to give you the results that you want. The Dryer jar allows for cooling and separation of water from hydrogen gas and keeps impurities and particles from entering your engine. This is the most efficient and safest way I have found to use this system. Now you can enjoy these benefits. Gain in horsepower and torque in all ranges. Up to 25% increase in engine power. Carbon deposits will be removed from your engine as you drive. Pass SMOG and EChecks easily. Your engine will add oxygen to the environment instead of polluting it. Complete Installation instructions included. Hydrogen-On-Demand means you generate Hydrogen when you need it, and use it immediately! There is no storage for later use of any kind. The Hydrogen is created by applying voltage to electrodes attached to stainless steel plates, and placed in a electrolyte solution. This produces hydrogen gas, oxygen, and water vapor that’s sent to the dryer jar by engine vacuum. Water is heavier and drips to the bottom of dryer jar. The gas rises and is used by your engine. This process creates less heat and steam to prevent thermal runaway. The hydrogen and oxygen gas created is used by your engine to burn fuel that is normally not ignited in the combustion process. Making your engine more efficient and creating more power, torque, and fuel savings. Hydrogen gas (HHO) is much more powerful than standard fuel and burns cleanly in the combustion process. Ridding your engine of harmful carbon deposits and lowering the operating temperature of the engine. Minutes after installing this unit you will notice a quieter engine and a smoother idle. Your engine will be more responsive with better acceleration. Your transmission will shift easier with less noise. You will notice the increase in power and acceleration right away. Fuel mileage isn’t the only great benefit that you should expect. A cleaner engine with less carbon deposits as you drive. Less carbon emissions in the atmosphere will allow you passa smog test if you’ve had trouble before. You engine will run cooler and your oil will be cleaner and your vehicle will last longer. It’s almost impossible to state the exact amount of fuel savings you will receive because everyone drives in a different way. I’ve used this unit on a variety of cars and trucks and the fuel saving will be noticeable after the first week. This all depends on driving conditions, weather, and condition and maintenance of vehicle. The amounts stated are estimates for cars and trucks in good mechanical condition. The HHO Generator with Dryer is quality constructed of 316L stainless steel and built to last many years. It doesn’t corrode under the heavy exposure to current, or the alkaline base of the electrolyte. Stainless steel plates are the most efficient of the designs, using less energy per square inch, leaving most electrical energy to convert water into hydrogen and oxygen atoms. The larger exposed surface edges give them the ability to translate as much energy into HHO gas without losing as much energy in the form of wasted heat. That is why spiral coils of wire are so inefficient. You have so very little metal actually exposed (maybe a few square inches) compared to a plate design. The main electrodes and the. 050” stainless steel plates, washers, and nuts are stainless steel, and all insulators are nylon. Two quart jars with stainless steel screw-on caps with silicone seals. High performance HPDE fittings are used throughout, including a pressure release valve in main jar for safety. The Installation kit comes with diagrams, maintenance, and general information. Included is all the necessary parts you’ll need for installing the system on your gasoline or diesel engine. It allows you to attach the system to your intake manifold and the air intake. Included are the following items. 1 – 10 foot coil of 1/4 Automotive Silicone Vacuum Hose. 2 – 1/4 Hose-barb Union Tee. 1 – 3/16”x 3/16” x 1/4” Hose -barb Tee. 1 – 1/4” x 1/4” x 1/4” Hose-barb Tee. 1 – 5/16” x 5/16” x 1/4” Hose-barb Reducer Tee. 1 – 3/8 x 3/8” x 1/4” Hose-barb Reducer Tee. 1 – 1/2x 1/2” x 1/4” Hose-barb Reducer Tee. 1 – 1/4” Hose Adapter. 2 – Hose Clamps. 1 – 15 amp Inline Water Tight Fuse Holder. 2 – 15 amp Fuses. 1 – 15 amp Circuit Breaker Auto Reset – Metal with Bracket. 1 – 5-foot coil of Red 14 AWG Electrical Wire. 1 – 3-foot coil of Black 14 AWG Electrical Wire. 3 – 16-14 AWG Butt Connectors. 6 – 16-14 AWG Wire Male and Female Disconnect Connectors. 2 – 1/4 Ring Terminal for Ground. 4 – 16-14 AWG Ring Terminals for Circuit Breaker. 2 – 1/4” AWG Ring Terminals for Electrode Bolts. 2 – 1/4 Stainless Steel Wing Nuts for Electrode Bolts. 1 – 2 ounces electrolyte with spoon. HHO Vacuum Pressure Hydrogen Generator with Dryer. We would like to hear from you to address your interest, concerns, or installation. Bill, You brought new life into this old daily driver. The HHO Kit that you installed did everything you said it would and more.. Bill, I thought you were full of it, but you proved me wrong. My 10 year old Chevy Truck runs like new, because of HHO. Dad – you made my little Fiat run like the wind and better gas mileage too! Love You – Jen. The item “HHO Hydrogen Generator Kit 1 Cell with Dryer for Gas and Diesel Engines” is in sale since Wednesday, November 4, 2020. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Other”. The seller is “billm007″ and is located in Youngstown, Ohio. This item can be shipped to United States.
- Modified Item: No
- Country/Region of Manufacture: United States
- Custom Bundle: No
- Material: Stainless Steel
- Type: Hydrogen Generator
- Manufacturer Part Number: HGWD3673
- Brand: BillMake
- Fitment Type: Performance/Custom
- Non-Domestic Product: No
- Warranty: 30 Day
- Mounting Hardware Included: Yes